*REAR WHEEL DRIVE ONLY*
BODY:
o Must be stock appearing and acceptable to the Technical Inspector. . May build doors, quarters, sail panels, and fenders, but must resemble stock. Roof 46 wide x 44 long Sail panels must be stock or if built, flat 8 inch top 18 inch bottom.
o Must run stock appearing nose and tail No md3 or late model style. Rear spoilers 6 inch tall no wider than trunk lid. Spoiler side 6 x 12. Stock spoiler OK. May enclose interior.
- Must have windshield
ROLLCAGE:
o Must Be minimum 1.50" OD tubing, minimum .095" steel wall thickness. Must have minimum 3 driver side door bars and 2 passenger side door bars. Must have support bars behind drivers and must be welded to frame. Must have minimum 3 windshield protection bars. Window nets are recommended . Must have approved aluminum racing seat.
CHASSIS:
o STOCK. May tie together. Must have stock floor pan and firewall no fabricated type.
SUPENSION:
o Must be stock and match model claimed. Racing springs allowed, 5" diameter minimum. Jack bolts and/or lowering blocks allowed. Steel body, non-adjustable racing shocks allowed. Must be mounted in STOCK location unless using jack bolts. Must use stock upper AND lower control arms. Caster/Camber adjustment plates allowed. Pinto may run adjustable lower strut arms mounted in stock position.
REAREND:
o Stock OEM, 7.5, 8 inch, 8.8, or 9 inch may lock. No independent rear suspensions.
STEERING:
o Stock box or stock rack. No aftermarket racks. May use heim joints on tie-rod ends.
o Quick release racing steering wheel recommended.
BRAKES:
o Steel caliper front, drum ONLY rear. No brake adjusters to master cylinder within arms reach of driver. May run three wheel brake.
WHEELBASE:
o Stock for model claimed, 1" tolerance. 92" minimum.
WHEELS:
o 13x8" racing wheels
TIRES:
o 205 60 13 Legend Tire (no soaking)
Racers must purchase tires from track, you can purchase a set for $60
WEIGHT:
o 1lb per CC - 2,300lb minimum
ENGINE:
o A. Stock 4 cylinder engine for model claimed. No rotary, turbo charged, or supercharged engines. No mid or rear engine cars. Engine must remain in stock location, NO setback.
o B. Block - Steel OEM block only. Max .060 overbore size 3.845 ford .005 tolerance. Zero deck. Plus or minus .003 tolerance.
o C. Crank, rods, pistons maybe balance. No windage trays or crankshaft scraper.
Stock cranks, no lightening or cutting other than balancing allowed.
o D. Rods - Steel OEM rod only. Ford rod length (5.2047) must have part number on rod. May use aftermarket rod bolts. Stock stroke only (Ford 3.126). Plus .006 tolerance. Rod may be brushed. Any flat tappet hydraulic cam. Must have hydraulic working lifters no tampering with inside of lifter. Lash caps ok. No shims allowed..
o E. Head - Stock OEM head only. May cut head; No angle milling, 0.010 tolerance; No Port or Polish; No cutting past valve seats; Double springs allowed. Steel retainers; Adjustable cam sprocket allowed. Stock diameter valves. (Ford Intake Valve 1.740 / Ford Exhaust Valve 1.500, 11/32 Stem, valve maybe back cut. No ranger valves).
o F. Piston - Any stock-type replacement piston allowed. Must have brow.
o G. Intake - Stock OEM only. Fuel injection intake allowed. 2-1/2 spacer max with gaskets, no porting allowed.
o H. Exhaust - May run aftermarket header or stock manifold.
o I. Oil Pan - Wet sump only.
o J. Carburetor - Must Pass no-go gauges. Holley 4412 500cfm 2 barrel max. NO fuel injection systems.
o K. Flywheel - Steel flywheel only, stock type replacement clutch only, no "button type". Stock pressure plate.
o L. No forced induction, boxes, ductwork.
TRANSMISSION:
o Any stock OEM, manual or automatic. Must have working stock type clutch, Must have sprung Hub with 360 degree Pad, ( NO puck Type) all forward gears and reverse.
o # Pressure Plate must be Stock Replacement Diaphrahm Type 7 ½ Min ( No Button Type)
IGNITION:
o Any stock OEM with stock replacement internals any coil. No traction control. Battery must be securely mounted with steel strap.
FUEL:
o May run racing fuel. Electric fuel pump ok BUT MUST HAVE SAFETY SHUT OFF SWITCH. Fuel cell or track approved tank attached with minimum of two (2) 2" wide steel straps. Gas only, No nitrous. Racing fuel must float a maximum specified gravity of 750. No E-85 fuel permitted.
SAFETY:
o All cars and drivers' safety equipment must meet general safety rules.
PROTESTS:
o Any car found illegal following qualifications or heats must prove to be legal before starting feature event.
o Any driver who is protested and refuses teardown, will be considered illegal and will start on the rear of their next feature event, regardless of qualifying position.
o Pull Head: $200 complete head carburetor an intake (Track Retains 30%)
o Bore & Stroke: $200 ( Track Retains 30%)
o Complete: $400 (Track Retains 30%)
o Fuel: $50 (Track Retains 100%)
All protest ( engine, buy rules) with the exception of a visual is to be done after the race is completed.
ROLL CAGE:
o Four Point minimum with 3 driver door bars minimum.
SEAT:
o Aluminum racing seat and safety harnesses are required.
BODY:
o Doors must be welded shut, remove all trim, upholstery and glass.
HEADER:
o May run header.
BODY / DRIVELINE &SUSPENSION:
o Must remain stock, in stock location for make and model.
SPRINGS:
o Stock springs may be cut.
STANDARD TRANSMISSION:
o Must have 2" inspection hole in bell housing.
MISCELLANEOUS:
o Must have Haynes or Chilton Manual for Teardown.
o Rear of cars MUST be enclosed.
o Cars must have windshields
o Cars must have window nets on driver side.
PROTEST FEES:
o Visual; $50 (Track Retains 100%)
o Clutch: $100 (Track Retains 100%)
o Engine: $300 (Track Retains 30%)